Delta Plc

Product Details:

• New 32-bit SoC (System on Chip) CPU to enhance execution speed 40 k steps / ms

• Positioning control function for up to 8-axis motion control via CANopen / 6-axis 200 kHz pulse control

• Robust non-backplane design and patented DIN rail clips for vertical module installation and replacement

• ISPSoft editing software for programming, hardware configuration, network communication, system diagnostics and positioning planning

Automated equipment such as electronics manufacturing, labeling, food packaging, and textile machines

1. New 32-bit SoC (System on Chip) CPU
2. Max. I/O: 1,024
3. Program capacity: AS300 series 128k steps, AS200 series 64k steps
4. Data registers: 60k words
5. Extension modules: max. 32 (analog modules: max.16 / communication modules: max. 4)
6. Execution speed: up to 40 k steps / ms
7.      - Basic instruction (LD): 25 ns
8.      - Application instruction (MOV): 0.15 μs
9. Abundant selection of DIO modules, AIO modules, temperature modules, load cell module and function cards.

Product Details:

1. CPU:
   - 32-bit high-speed processor
   - Built-in I/O points: 32 / 48 / 64 / 80
2. Program capacity: 64k steps
3. General register: 64k words
4. Communication ports: RS-485 * 2, Ethernet * 1, and CANopen DS301 * 1
5. Built-in SD interface (Micro SD)
6. Max. I/O points: 256 points (256 inputs / 256 outputs)
7. 4 high-speed counters: maximum frequency 200 kHz for each counter
8. 4-axis (8 points) high-speed position output at 200 kHz
9. Supports a total of 8-axis (CANopen) position outputs
10. Supports IEC61131-3 programming (LD, ST, SFC and CFC)

Product Details:

1. MPU points: 16 / 20 / 24 / 32 / 40 / 60
2. Program capacity: 16k steps
3. Built-in with 3 COM ports: 1 RS-232 port and 2 RS-485 ports, all are able to operate independently (Master/Slave)
4. Max. I/O points: 256 input points + 16 output points, or 256 output points + 16 input points
5. DVP-EX2 MPU is built in with 12-bit 4AD/2DA and offers analog/temperature modules of 14-bit resolution.
6. Built-in with 8 high-speed input points (2 points for 100kHz, 6 points for 10kHz) and supports U/D, U/D Dir, A/B counting modes
7. New motion control instructions: Close loop control, alignment mark, shield, immediate variable speed, S-Curve acceleration/deceleration
8. Application in emerging industry: Exclusive instructions and function blocks designed for PV solar tracker
9. Handy instructions for frequency inverter: For controlling the forward running, reverse running, RUN and STOP of Delta@@s AC motor drives
10. Password protection: Password for subroutine, user ID, restriction on trial times
11. Highly efficient instruction efficient instruction execution

Product Details:

• Modularized Hardware Structure, Highly Integrated Software
• Highly integrated software ISPSoft: Graphical Interface with 5 programming languages
• Enhanced flexibility: Max. 100m between 2 local extension racks
• Improved maintainability: Hot-swapping function keeps the system running

Large Scale Industrial Machines

The AH500 supports excellent motion control functions including 3-axis linear interpolation, 2-axis arc interpolation, and 3-axis helical interpolation. In addition, the AH500 is capable of controlling up to 12 axes or 4 groups of 3-axis interpolation synchronously at 1ms through Delta's high speed DMCNET motion control network. The AH500 satisfies requirements for complex processing or precise motion control and is effective for applications such as building material processors, warp knitting machines and food packaging machines.

1. Utilizes 32-bit processor
2. Excellent program execution speed LD instruction execution speed 0.02µs
3. Max. I/O points:
     - DIO: Max. 4,352 points
     - AIO: Max. 544 channels
     - RIO>100,000 points
4. Program capacity Max 384k steps (1.5MB)
5. Data register (D+L) 256k words
6. CPU built-in with fully isolated RS-232/422/485 Mini USB Ethernet full-size standard SD(standard CPU)/SDHC(advanced CPU) card slot
7. Abundant selection of DIO modules, AIO modules, temperature control modules, network modules, pulse-train modules and DMCNET / EtherCAT motion control modules

Product Details:

High-speed 3-axis servo welding machine, high-speed cutting machine, bar feeder, distributed monitor system in production line.

1. High-speed pulse output: 4 sets of 200kHz pulse output (DVP40/48/64/80EH00T3)
2. Supports max. 4 hardware 200kHz high-speed counters
3. Increases many motion control instructions to meet the applications that require high-speed and high-precision
4. positioning control such as labeling machines, packaging machines and printing machines
5. Offers linear / arc interpolation motion control
6. Provides up to 16 external interrupt pointers

1. Auto backup function to prevent losing programs and data even when the battery runs out
2. Second copy function provides a backup for extra insurance in the event that one set of programs and data are damaged
3. Up to 4-level password protection protects your source programs and intellectual property

1. CPU + ASIC dual processors support floating point operations.
2. The max. execution speed of basic instructions is able to reach 0.24μs.

1. The multiple selections of extension modules and function cards provide analog I/O, temperature measurement, additional single-axis motion control, high-speed counting, 3rd serial communication port and Ethernet communication card are available.

1. C-Link allows the user to link up a max. 32 units to the network without having to install extra communication extension modules.

Product Details:

Used for PID temperature/humidity control, 2-axis AC motor drive constant speed control, temperature control using a analog signal monitoring of a whole factory. (PLC EASY LINK)

1. MPU points: 20 (8DI/6DO, 4AI/2AO)
2. Max. I/O points: 494 (14 + 480)
3. Program capacity: 16k steps
4. COM port: Built-in RS-232, RS-485 & USB ports, compatible with ASCII/RTU protocol. Can be master or slave.
5. High-Speed Pulse Output: Supports 2 points (Y0, Y2) of 100kHz and 2 points (Y1, Y3) of 10kHz independent high-speed pulse output.
6. Built-in High-Speed Counters
7. Built-in Analog I/O

Product Details:

2-axis servo positioning control, material cutting machine (high-speed servo control), main hoist of crane, material clip controlled by servo, equipments in the optoelectronics industry, semiconductor industry, textile industry, energy saving activities and automation in buildings.

1. High-speed pulse output: 4 sets of 200kHz pulse output
2. Supports max. 4 hardware 200kHz high-speed counters
3. Increases many motion control instructions to meet the applications that require high-speed and high-precision positioning
4. Offers linear / arc interpolation motion control
5. Provides up to 16 external interrupt pointers

1. Auto backup function to prevent losing programs and data even when the battery runs out
2. Second copy function provides a backup for extra insurance in the event that one set of programs and data are damaged
3. Up to 4-level password protection protects your source programs and intellectual property

1. Add new ETHRW instruction for Ethernet communication

Product Details:

• The most complete network type slim PLC in the industry

• Provides 8 digital inputs and 4 digital outputs

• Built-in mini USB, Ethernet, and 2 RS-485 ports

Remote device monitoring, production line monitoring, building automation, printing machine, container filler (recipe application)

1. Program capacity: 16k steps
2. Data register: 12k words
3. Higher execution speed compared to the competition: LD: 0.64μs, MOV: 2μs
4. Built-in Ethernet supports MODBUS TCP and Ethernet/IP
5. IP Filter function is a firewall that offers the first line of defense and provides protection from malware and network threats
6. Supports DVP-S series left-side and right-side modules
7. No battery required. Maintenance-free.(Real time clock operates for 15 days after power off)

Product Details:

Single control unit, landscape fountain, building automation

1. MPU points: 10/ 14 / 16 / 24 / 32 / 60
2. Max. I/O points: 60
3. Program capacity: 4k steps
4. COM ports: Built-in RS-232 and RS-485 ports (available in 16-60 point models); compatible with Modbus ASCII/RTU protocol
5. Built-in 4 points of high-speed counters*:

Product Details:

Used for PID temperature/humidity control, 2-axis AC motor drive constant speed control, temperature control using a analog signal monitoring of a whole factory. (PLC EASY LINK)

1. MPU points: 10 (4DI/2DO, 2AI/2AO)
2. Max. I/O points: 230
3. Program capacity: 8K Steps
4. Communication port: Built-in RS-232 and RS-485, compatible with MODBUS ASCII / RTU communication protocol.
5. High-speed pulse output: Supports 2-point independent high-speed pulse output (Y0 of up to 50KHz and Y1 of up to 10KHz).
6. Built-in high-speed counter

Product Details:

Printing machine, dying machine, container filler (for prescription’s), work station monitoring in production line (PLC EASY LINK)

1. MPU points: 12 (8DI + 4DO)
2. Max. I/O points: 492 (12 + 480)
3. Program capacity: 16k steps
4. COM port: Built-in RS-232 & 2 RS-485 ports, compatible with Modbus ASCII/RTU protocol.
5. Can be master or slave.
6. High-Speed Pulse Output: Supports 2 points (Y0, Y2) of 100kHz and 2 points (Y1, Y3) of 10kHz independent high-speed pulse output.
7. Extendable to Max. 8 Modules: DVP-SA2 is extendable to analog I/O, temperature measurement, input DIP switch, PROFIBUS/DeviceNet communication modules and single-axis motion control functions.

Product Details:

Spinning machine, conveyer belt (rotation speed control), winding machine (tension control)

1. MPU points: 14 (8DI + 6DO)
2. Max. I/O points: 494 (14 + 480)
3. Program capacity: 8k steps
4. COM port: Built-in RS-232 & RS-485 ports, compatible with Modbus ASCII/RTU protocol. Can be master or slave.
5. High-Speed Pulse Output Supports 4 points (Y0 ~ Y3) of independent high-speed (max. 10kHz) pulse output
6. Supports PID Auto-tuning DVP-SS2 saves parameters automatically after the PID auto temperature tuning is completed.
7. Built-in High-Speed Counters